Yaesu ft 70d программирование

CoyoteSwamp

Dangerous toys. Too much caffeine. Advanced degree in physics. This isn’t going anywhere you want to be.

Saturday, June 27, 2020

Yaesu FT-70DR Quick Start Programming

Riffing on an earlier post Yaesu FTM-7250 Quick Start Programming, here is the same for the FT-70DR handheld. Also, full credit for this goes to KE0MJE for his youtube video on how to do all this. This post is really nothing more than a cleaned-up version of the notes that I took while watching. If you want to watch the video before you dive into the checklists below, go have a look. It might help, and you can always come back to the detailed checklists below. Finally, there’s the Radio Programming Roundup page, that has a bunch of links to programming some other radios and details on using CHIRP.

Remember, «press» means «press momentarily,» while «press and hold» means for about 1 second.

1. Turn radio ON.
2. Press [V/M] key to go to VFO mode.
3. Enter receive frequency on keypad.
4. Press [Mode] key to toggle to your preferred mode: FM or Digital. (DN? why DN for digital?)
5. Press [F] then [5 / Sq Typ] to get to squelch type selection.
6. Rotate dial to pick the right squelch type. OFF / TONE / TSQL are all useful possibilities on standard repeaters.
7. Press [F] to leave tone/squelch type set.
8. Press [F] then [6 / Code] to get to the tone frequency selection.
9. Rotate dial to the repeater’s tone frequency.
10. Press [F] to leave tone frequency set.
11. To save all this into a memory slot, press and hold [V/M]. «F» will flash on the screen, along with the memory slot number it’s going to use.
12. Dial to a memory slot you want to write this information into. If the memory slot number is flashing it’s empty; if it’s not flashing, it’s in use, but can be over-written.
13. Press [V/M] to save to that memory slot. An alphanumeric tag entry is automatically started. If radio asks, confirm with another press of [V/M].
14. Rotate knob to scroll to letters; press [Band] to save each letter and move to the next letter slot. If you need to back up, use the [Mode] key. When you’re done entering the alphanumeric tag.
15. Press and hold [V/M] to save.
16. Press [V/M] to get to memory mode. You should see the new alphanumeric tag and be all set.

Читайте также:  Stm программирование через arduino

Painless. especially when you have the Auto Repeater Shift and Automatic Mode Select set. (they’re the as-shipped defaults)

Simplex channel programming is even easier. With no CTCSS tones to bother with, it’s a snap. In fact, before programming simplex channels it’s best to turn tones off. See steps 5 & 6 above. But if you don’t, or forget, or. it really won’t matter.

1. Turn radio ON.
2. Press [V/M] key to go to VFO mode.
3. Enter receive frequency on keypad.
4. Press [Mode] key to toggle to your preferred mode: FM or Digital. (DN? why DN for digital?)

6. To save all this into am memory slot, press and hold [V/M]. «F» will flash on the screen, along with the memory slot number it’s going to use. If you just want the frequency to show, skip to step 10.
7. Dial to a memory slot you want to write this information into. If the memory slot number is flashing it’s empty; if it’s not flashing, it’s in use, but can be over-written.
8. Press [V/M] to save to that memory slot. An alphanumeric tag entry is automatically started. If radio asks, confirm with another press of [V/M].
9. Rotate knob to scroll to letters; press [Band] to save each letter and move to the next letter slot. If you need to back up, use the [Mode] key. When you’re done entering the alphanumeric tag.
10. Press and hold [V/M] to save.

Not as bad as it looks. If you have a list of repeaters and simplex frequencies ready to go, once you get rolling it doesn’t take long at all. Many of the settings will just repeat, and you can skip over some of the option changes when that happens.

Edit 7/1: Took out the «FM» on repeater operations because these instructions aren’t limited to FM anymore. Also note, even if your (say) simplex channel is programmed in to default to FM (or digital), a press of the [Mode] key will flip it to the other mode.

CHIRP allegedly works with this radio, but damned if I could get it to go on either my Mac or Linux systems. It involves the most harebrained pop-the-battery-out-now-in sequence I’ve ever seen. Probably not worth the bother.

Anyway, I picked up one of these little jewels this week from Main Trading Company Radio (you should do business there, they’re good folks). The FT-70 stacks up well in comparison to its predecessor FT-60. It may not be quite as rugged, but it is well built and seems tough enough to be of real use in the field. The dials have been reduced to one, with some trivial combos of [F], [Moni], [Vol], and a dial twist go get you where you want. Beyond that, the significant upgrades are Fusion digital mode, and a lithium ion battery pack. Fusion is amazing, giving clear communications over longer ranges than FM; you can read about that elsewhere. The lithium battery shouldn’t have the memory issues of the older NiMH pack on the FT-60. There’s been some justifiable grumbling about battery draw when the FT-70 is turned off. Meh, just pop the battery pack if you’re going to let it sit for more than a couple of days. It’s not great, but there are bigger issues in life to worry about.

In short, it’s an updated FT-60. Could it have been better? Sure. Is it a good radio for the price? Definitely.

Источник

Yaesu: Yaesu FT-70D programming issues

Has anyone experienced a no programming with the USB failing? That is my issue ! Cannot program my FT-70 using Chirp keeps telling me the USB is not working.

k9wkj

Member

dont use chirp, it does not handle mode selection properly (at all)

use the factory software and follow the instructions

KO4IPV

Member

dont use chirp, it does not handle mode selection properly (at all)

use the factory software and follow the instructions

ko6jw_2

Member

I recommend the RT Systems software. Both Chirp and the OEM Yaesu software flailed. Could not program banks. Only RT has worked. I already had the programming cable from other radios. Do not use Chirp. May damage the radio and void warranty.

KO4IPV

Member

I recommend the RT Systems software. Both Chirp and the OEM Yaesu software flailed. Could not program banks. Only RT has worked. I already had the programming cable from other radios. Do not use Chirp. May damage the radio and void warranty.

cmdrwill

Member

do not use chirp, it does not handle mode selection properly (at all)
use the factory software and follow the instructions

bill4long

Member

RT System’s software is generally excellent. Do you actually have experience with their software for the FT-70?

KO4IPV

Member

RT System’s software is generally excellent. Do you actually have experience with their software for the FT-70?

No only with Chirp and Sentinel software what is RT systems software? Is this something I can download?

AK9R

Lead Wiki Manager and almost an Awesome Moderator

The Yaesu software can be downloaded from the Yaesu website. K9WKJ gave you the link, but here it is again:

RT Systems is a third-party software developer. You can buy their software on their website:

bill4long

Member

No only with Chirp and Sentinel software what is RT systems software? Is this something I can download?

$30. I use two dozen variants of their software, because it makes it easy for me to manage a lot of different radios, with a lot of frequency/channel overlap. The other user cmdrwill seemed to be implying that RT Systems software was on par with CHIRP. It isn’t. It’s a lot better. But there is no reason to use RT if the free Yaesu software does the job.

Источник

Оцените статью